電子天平打開后，如果其顯示屏上沒有顯示，說明電子秤出現了故障。

失敗原因：天平沒有真正打開；無電源或臨時停電；電源插頭接觸不良；保險絲損壞；變壓器整流器損壞；電子天平電壓塊選擇不當；電源電壓瞬間受到干擾；顯示器損壞；電子天平A/D轉換器可能有問題；電子天平的微處理器可能有故障。

調整方法：

再次打開電子天平；用電壓表檢查外部電源。確認沒電后，就關機等電；仔細檢查電源插頭，使其接觸良好。如有必要，使用萬用表檢查電線是否斷裂。更換同規格同型號的保險絲；修理或更換電源變壓器整流器；正確選擇電子天平的電壓塊，使其與當地電壓一致；如果電源電壓過低，暫時關機，待電源電壓穩定后再打開天平；修理或更換電子天平的顯示器；檢修或更換電子天平的A/D轉換器；修理或更換電子天平的微處理器。

電子天平的顯示屏只顯示下半部分，說明天平有問題，應立即修理。

故障原因：稱重系統有摩擦卡阻現象；秤盤未安裝或安裝錯誤；打開天平后，物品從秤盤中取出。

調整方法：檢查稱重系統，排除卡澀等故障；安裝秤盤。如果幾套同時安裝，不要裝錯。打開天平后，將物品從秤盤中取出，關機再開機，按規范操作。